Welcome! Log In Create A New Profile

Advanced

I am kind of a big deal.

Your perspectives on knife performance, observations you have made, questions you ponder, conclusions you have reached. 
This forum is currently read only. You can not log in or make any changes. This is a temporary situation.
Subject Views Posts Last Post

DMT Extra Fine seems rough?

by StanLee
2,311 10 03/24/2015 09:51PM
Last Post by stefan_wolf

carbidized edges

by wnease
2,067 8 03/15/2015 07:33PM
Last Post by Bugout Bill

Ways to measure the force of a cut

by Surhoff88
2,139 7 03/14/2015 05:01AM
Last Post by CliffStamp

Small folders for EDC

by jasonstone20
2,647 27 03/11/2015 08:52PM
Last Post by jasonstone20

EDC Edge Finish Experiment Data

by jasonstone20
1,426 5 03/11/2015 02:33AM
Last Post by jasonstone20

a Advertising Review

by dingy
1,456 5 02/28/2015 07:11AM
Last Post by Dropbear

Granton Edge

by CliffStamp
2,029 26 02/27/2015 09:28PM
Last Post by jasonstone20

Rubber band handle wrap.

by KWB
2,018 15 02/21/2015 03:19AM
Last Post by Ryan Nafe

Buck 371 Inconsistency

by Bugout Bill
2,878 8 02/15/2015 02:00AM
Last Post by Bugout Bill

Burr minimazation... thoughts?

by razoredgeknives
3,369 17 02/09/2015 05:22AM
Last Post by jasonstone20

Wear resistance of push-cut vs slicing-cut?

by Lagrangian
2,717 23 02/08/2015 10:45PM
Last Post by me2

Not a big deal. Would like to be someday..Books?

by Zamfir
1,217 2 01/29/2015 03:55AM
Last Post by CliffStamp

From Ridiculous to Ludicrous

by cKc
2,548 14 01/28/2015 03:01AM
Last Post by Stuart Ackerman

Micrometers and what they reveal

by Reijo
1,267 2 01/24/2015 03:48AM
Last Post by razoredgeknives

Full Flat grind knives. I actually don't have one. Yet.

by TerriLiGunn
1,486 4 01/22/2015 08:25AM
Last Post by TerriLiGunn

chinese products bias

by dingy
2,113 13 01/18/2015 01:31PM
Last Post by fugglesby

why can't I have it all......?

by KWB
2,012 11 01/03/2015 12:02PM
Last Post by KWB

HC steels & simple steels = same edge retention?

by DK
1,700 15 01/01/2015 04:34AM
Last Post by me2

Edge Rippling and Edge Blowouts

by Chum
1,462 14 12/27/2014 06:56PM
Last Post by CliffStamp

Buffing wheel overheating effect - affects H1, D2, M4 and other tool steels?

by WobblyHands
2,600 7 12/15/2014 03:12PM
Last Post by WobblyHands

Problem with spyderco stones   (Pages: 1 2)

by KWB
4,238 40 12/05/2014 03:37AM
Last Post by Bugout Bill

Definition of sharp

by razoredgeknives
1,532 5 12/04/2014 07:50PM
Last Post by Mark a

I was mistaken before........

by KWB
1,286 5 12/03/2014 05:41PM
Last Post by jasonstone20

Sharpening stone finer than Spyderco's UF?

by StanLee
1,632 13 11/30/2014 10:45AM
Last Post by PhatMan

Tramontina Machetes inc Bolo - Questions and comparisons   (Pages: 1 2)

by AdamJ
5,477 55 11/29/2014 10:24PM
Last Post by Mark a

cable tang bias

by dingy
4,532 18 11/26/2014 01:38PM
Last Post by fugglesby

Jerry Hossom' design

by dingy
3,431 25 11/17/2014 05:49PM
Last Post by Mark Nelson

Carbide volume in PM steel   (Pages: 1 2 3)

by Eee
5,702 62 11/12/2014 09:45AM
Last Post by Bogdan M.

The concrete analogy

by Reijo
1,233 5 11/08/2014 11:51AM
Last Post by wnease

Spyderco Terzuola Starmate (Or Problems with Tactical Folders)

by Bugout Bill
2,118 11 11/06/2014 08:23PM
Last Post by Bugout Bill