Things that are actually ok - sharpening videos
Posted by CliffStamp
|
Re: Things that are actually ok - sharpening videos September 06, 2016 06:03PM |
Registered: 5 years ago Posts: 437 |
Sharpening serrated knife edge with sandpaper - stefanwolf88
materials
- abrasive, a square of sandpaper, ?P180
- a wooden skewer, a skinny round rod
- binder clip, paperclip, use it to secure sandpaper tightly around skinny rod, its also your handle
the serrations are chisel ground,
so grind one side only until raise burr
grind each serration separately
also give a few passes over entire serrated section ,
not too much dont want to grind down the tips too much
then release the sandpaper from clip,
and use the paper square backed with your thumb
on other side of knife to remove burr
feel for burr to make sure its gone
repeat as needed
no cutting demo or text or talking ...
but its clear and simple enough demonstration to follow
____
Thanks
I don't mow
materials
- abrasive, a square of sandpaper, ?P180
- a wooden skewer, a skinny round rod
- binder clip, paperclip, use it to secure sandpaper tightly around skinny rod, its also your handle
the serrations are chisel ground,
so grind one side only until raise burr
grind each serration separately
also give a few passes over entire serrated section ,
not too much dont want to grind down the tips too much
then release the sandpaper from clip,
and use the paper square backed with your thumb
on other side of knife to remove burr
feel for burr to make sure its gone
repeat as needed
no cutting demo or text or talking ...
but its clear and simple enough demonstration to follow
____
Thanks
I don't mow
|
Re: Things that are actually ok - sharpening videos September 06, 2016 07:11PM |
Registered: 5 years ago Posts: 437 |
Quote
ShaperAndMower
Sharpening serrated knife edge with sandpaper - stefanwolf88
materials
- abrasive, a square of sandpaper, ?P180
- a wooden skewer, a skinny round rod
- binder clip, paperclip, use it to secure sandpaper tightly around skinny rod, its also your handle
the serrations are chisel ground,
so grind one side only until raise burr
grind each serration separately
also give a few passes over entire serrated section ,
not too much dont want to grind down the tips too much
then release the sandpaper from clip,
and use the paper square backed with your thumb
on other side of knife to remove burr
feel for burr to make sure its gone
repeat as needed
no cutting demo or text or talking ...
but its clear and simple enough demonstration to follow
also, sandpaper has a grain
the paper backing has a grain
like wood has grain
or newspaper has grain,
the sandpaper bends smoother in one direction than the other
so if you want it to bend and warp smoothly around a skewer,
figure out which direction bends smooth BEFORE
you cut off a strip
____
Thanks
I don't mow
|
Re: Things that are actually ok - sharpening videos September 20, 2016 05:16PM |
Admin Registered: 5 years ago Posts: 5,683 |
This guy has a nice YouTube channel for sharpening videos:
DMT XXC, XC, C, F, XF progression on Ganzo 440C
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
DMT XXC, XC, C, F, XF progression on Ganzo 440C
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos September 04, 2017 10:21AM |
Admin Registered: 5 years ago Posts: 5,683 |
MC and BBG:
MC:
[youtu.be]
BBG:
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
MC:
[youtu.be]
BBG:
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos September 14, 2017 01:51PM |
Admin Registered: 5 years ago Posts: 5,683 |
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos September 14, 2017 08:06PM |
Admin Registered: 5 years ago Posts: 5,683 |
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos September 15, 2017 07:58PM |
Admin Registered: 5 years ago Posts: 5,683 |
I don't agree with everything advised in these two videos, but he's close enough to get you a sharp knife:
Outdoors55:
[www.youtube.com]
[www.youtube.com]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
Outdoors55:
[www.youtube.com]
[www.youtube.com]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos September 15, 2017 09:17PM |
Admin Registered: 5 years ago Posts: 5,683 |
The Sharpie/Magic Maker trick demonstrated:
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos September 20, 2017 10:34AM |
Admin Registered: 5 years ago Posts: 5,683 |
Peter Nowlan's and Jon Broida series for KnifePlanet.net:
Lesson 1:
[www.youtube.com]
Lesson 2:
[www.youtube.com]
Lesson 3:
[www.youtube.com]
Lesson 4:
[www.youtube.com]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
Edited 1 time(s). Last edit at 09/20/2017 10:35AM by jasonstone20.
Lesson 1:
[www.youtube.com]
Lesson 2:
[www.youtube.com]
Lesson 3:
[www.youtube.com]
Lesson 4:
[www.youtube.com]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
Edited 1 time(s). Last edit at 09/20/2017 10:35AM by jasonstone20.
|
Re: Things that are actually ok - sharpening videos September 22, 2017 12:42PM |
Registered: 6 years ago Posts: 589 |
|
Re: Things that are actually ok - sharpening videos January 24, 2018 11:42AM |
Admin Registered: 5 years ago Posts: 5,683 |
Patron Saint of Knives:
[youtu.be]
He lives pretty close to Portland, OR, in Vancouver WA. I keep meaning to talk to him and maybe visit his shop. He gave me his phone number when I commented that I live in close to him.
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
Edited 1 time(s). Last edit at 01/24/2018 11:44AM by jasonstone20.
[youtu.be]
He lives pretty close to Portland, OR, in Vancouver WA. I keep meaning to talk to him and maybe visit his shop. He gave me his phone number when I commented that I live in close to him.
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
Edited 1 time(s). Last edit at 01/24/2018 11:44AM by jasonstone20.
|
Re: Things that are actually ok - sharpening videos January 26, 2018 12:42PM |
Admin Registered: 5 years ago Posts: 5,683 |
Sharpening a carving knife using mill file, carbide sharpener, diamond sharpener, and strop:
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos February 04, 2018 10:29AM |
Admin Registered: 5 years ago Posts: 5,683 |
Pete from the Cedric & Ada using the Lansky to do a knife sharpening:
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos February 07, 2018 10:07PM |
Admin Registered: 5 years ago Posts: 5,683 |
Survial Lilly video:
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos March 10, 2018 02:07PM |
Admin Registered: 7 years ago Posts: 12,464 |
|
Re: Things that are actually ok - sharpening videos March 10, 2018 03:50PM |
Registered: 5 years ago Posts: 2,823 |
|
Re: Things that are actually ok - sharpening videos March 10, 2018 07:49PM |
Admin Registered: 5 years ago Posts: 5,683 |
Cliff,
I saw that video a little while ago, that is a neat trick with the blocks at the end of the stones.
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
I saw that video a little while ago, that is a neat trick with the blocks at the end of the stones.
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos April 11, 2018 01:57PM |
Admin Registered: 5 years ago Posts: 5,683 |
Video:
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos April 21, 2018 07:10AM |
Admin Registered: 5 years ago Posts: 5,683 |
Video:
[youtu.be]
Nice simple technique with good results.
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
[youtu.be]
Nice simple technique with good results.
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos April 23, 2018 07:15AM |
Admin Registered: 5 years ago Posts: 5,683 |
Len McDougall from Tactical Knives on knife sharpening (video):
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos April 24, 2018 01:48PM |
Admin Registered: 5 years ago Posts: 5,683 |
Video:
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos April 26, 2018 10:47PM |
Admin Registered: 5 years ago Posts: 5,683 |
Sharpening a French paring knife-
Video:
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
Video:
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos April 27, 2018 09:28AM |
Admin Registered: 7 years ago Posts: 12,464 |
|
Re: Things that are actually ok - sharpening videos April 27, 2018 09:50AM |
Admin Registered: 5 years ago Posts: 5,683 |
Cliff,
I was thinking the same thing. I would have started at a lower grit for the flat side, gone up to the 1k stone, then the 3k, 6k, and stropped. Even if you use the Tormek for the hollow grind, I don't see the need of all the lapping films.
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
I was thinking the same thing. I would have started at a lower grit for the flat side, gone up to the 1k stone, then the 3k, 6k, and stropped. Even if you use the Tormek for the hollow grind, I don't see the need of all the lapping films.
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos April 28, 2018 03:58AM |
Registered: 4 years ago Posts: 680 |
flattening the back of a chisel grind on a 1k stone - not my cup of sharpening tea...
I like tormek machines - for a tradesman can be very useful piece of equipment
-------------------------------------------------------------------------------------------------------------
Life is GOOD!
[www.youtube.com]
I like tormek machines - for a tradesman can be very useful piece of equipment
-------------------------------------------------------------------------------------------------------------
Life is GOOD!
[www.youtube.com]
|
Re: Things that are actually ok - sharpening videos April 29, 2018 07:46AM |
Admin Registered: 5 years ago Posts: 5,683 |
Big Brown Bear sharpening Maxamet (video):
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos October 22, 2018 11:12AM |
Admin Registered: 5 years ago Posts: 5,683 |
Norton Oilstone Sharpening:
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos October 22, 2018 11:16AM |
Admin Registered: 5 years ago Posts: 5,683 |
Blade HQ: Spyderco Sharpmaker knife sharpening:
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
[youtu.be]
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos December 07, 2018 03:17PM |
Admin Registered: 5 years ago Posts: 5,683 |
First time knife sharpener uses Lansky Sharpener
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
|
Re: Things that are actually ok - sharpening videos March 18, 2019 10:37AM |
Admin Registered: 5 years ago Posts: 5,683 |
Mississippi Knife Nut with a Tangram knife and a KME Sharpener, showing that fixed systems don't have to be slow!
"Gotta love living in 2019 baby, (63rc too soft on a production knife)"
--Shawn Houston
"I am still discussing issues of steels and performance at this stage."
--Cliff Stamp
"Cause geometry cuts, .....steel determines the level and the duration"
--Roman Landes
"But in general, I'm all about high performance, Ergos, safety. That's why I've been accused of 'designing in the dark' "
--Sal Glesser
Sorry, only registered users may post in this forum.